ExpeditionExpedition Navigation Software


Click Here for Expedition Assistant - AI Chatbot

You are not logged in. Would you like to login or register?

1/06/2024 9:14 am  #1


h5000 Pilot and Expedition Waypoint(s)

I'm sorry if this has already been covered, but my searches here have found nothing.

I have just installed a new H5000 system on my boat after 20+ good H2000 years.  All is working fine, but I am having trouble getting the H5000 system to use/view the Expedition waypoint for Pilot navigation.

I have figured out how to transfer my waypoints to a Zeus MFD, and then create a route on the Zeus using those waypoints which is then picked up by the pilot.  But, that is far from an optimal solution.

Is there any way to have Expedition identified as a Navigation Source to simplify the process??

(I've installed the new Hercules Processor if that makes a difference.)

thanks for any help.

Last edited by JDG (1/06/2024 9:30 am)

 

1/10/2024 7:41 am  #2


Re: h5000 Pilot and Expedition Waypoint(s)

Wow.  No response at all?  I can't believe that I am the only one that has tried to make this work.  Perhaps its so simple that nobody wants to embarrass me by pointing out the easy solution.

     •Thread Starter
 

1/10/2024 8:41 am  #3


Re: h5000 Pilot and Expedition Waypoint(s)


:::Campbell Field::::::www.fieldyachting.com:::
 

1/10/2024 9:02 am  #4


Re: h5000 Pilot and Expedition Waypoint(s)

Thanks for your response. Those posts are close but not addressing my primary goal of passing an active waypoint from expedition to the h5000 pilot.

I can send waypoint info to the displays via across, but the pilot doesn’t seem to pick that up.

I can send the waypoint to my Zeus but I really don’t care about the Zeus. It’s here primarily for radar.

I’m looking for a “simple” way to have expedition and the h5000 pilot work together.

Open to any suggestions. Thanks again.

     •Thread Starter
 

1/10/2024 11:31 am  #5


Re: h5000 Pilot and Expedition Waypoint(s)

Maybe here:
https://expedition.boardhost.com/viewtopic.php?id=2090
I did a search on "zeus" and there is a lot out there,
you could try other search parameters...

Ernie M
 

 

1/10/2024 11:41 am  #6


Re: h5000 Pilot and Expedition Waypoint(s)

Thanks for your reply.  I never should have mentioned the Zeus.  

The Zeus is not part of my question.  (I guess it might be part of the answer?  But, I don't think so.)

I am looking for a way to get Expedition and my H5000 pilot to work with each other.  (Ex. I would like to create a route with one waypoint and be able to tell the Pilot to navigate towards that waypoint using the "Nav" pilot mode.)

Last edited by JDG (1/10/2024 11:42 am)

     •Thread Starter
 

1/10/2024 4:59 pm  #7


Re: h5000 Pilot and Expedition Waypoint(s)

If you are connected to the H5000 with he websocket connection and are sending the nav data, then the H5000 should regard Exp as the navigation source.

Prsumably that then affects the pilot downstream, but I know little about pilots.

 

11/18/2026 10:57 pm  #8


Re: h5000 Pilot and Expedition Waypoint(s)

Have you ever tried sending nav data (waypoint,xte,..) from Expedition to the H5000 Pilot CPU via NMEA 0183 port?

Last edited by gonzgo (11/18/2026 11:33 pm)

 

Yesterday 4:50 pm  #9


Re: h5000 Pilot and Expedition Waypoint(s)

Let me preface this by saying that this is NOT an Expedition issue.
It is 100% on the B&G side.

The H5000 Pilot does not accept anything other than B&G proprietary control PGNs.
The H5000 Pilot has no knowledge of waypoints, XTE, APB, APA, or anything else of that nature in N2K.

All of these are calculated by a B&G MFD and converted into a proprietary control PGN representing 1–10 degrees to port or starboard.

So, unless you can decode and generate the B&G control PGNs, it will not work.

The B&G workflow is:
  Expedition sends the waypoin/active mark to the B&G MFD, then the user makes that waypoin/active mark in the B&G MFD and then B&G MFD controls the H5000 Pilot.

The same is true for laylines.
Expedition can send a waypoint/active mark to the processor and/or the NMEA network, but no B&G display will accept that waypoint as the active mark.
Therefore, the display will not show laylines from that mark/waypoint unless Expedition sends the waypoint/active mark directly to the B&G MFD and makes it the active mark there.

The new B&G Zeus S family does not even process an incoming waypoint or route from Expedition.
Yes it is in the B&G documentation, It has been there since the H3000, many people has reached out to B&G and B&G has ignored the request.
The Zeus2 and Zeus 3 family will process waypoint/route PGNs from NMeA0183 and 2K.

BTW with the new Zeus S family you can't even send a MOB to the MFDs. Can you imagine that!?

Last edited by Astolfo (Yesterday 4:59 pm)

 

Board footera




Check out RaceData for iOS and Android. Expedition data in the palm of your hand, or on your wrist! RaceData

Interested in advertising here? Over one thousand active navigators and Expedition users visit this forum. Click here to contact the administrator.